Close
Søke

Tascam ML-32D

Produsent: TASCAM
SKU: 705937
kr 21 999,00 inkl MVA
32-in/32-out Analog-to-Dante Converter with 24-bit/96kHz Resolution, Dual Redundant Ethernet Jacks, AES67/Revenna Support, Selectable DBu Level Metering, and LED Display
0 Nettlager inkl. Butikker
Leverandørlager - Ukjent status
+ -
32-channel Analog/Dante Converter
The TASCAM ML-32D is a professional Dante-focused converter made specifically to insert or extract analog audio into or out of a Dante (Digital Audio Network Through Ethernet) network using external breakout devices that utilize Sub-D format connectors.

The ML-32D has four D-Sub inputs and four D-Sub outputs, which can easily be connected to any of the many devices that utilize D-Sub connectors such as microphone preamplifiers, large and small format console mixers, audio interfaces, amplifiers, and euro block connector devices. This simple, yet elegant, solution enables audio to be quickly and easily inserted into – or extracted from – the Dante audio stream.

Now compatible with SMPTE ST 2110-30
Dante module firmware V1.2.0.0 now supports SMPTE ST-2110-30, which will enable a smooth IP transmission of PCM digital audio for structuring broadcast systems.

* Audinate's provided Dante Domain Manager (DDM) v1.1 or higher is required for the operation of SMPTE ST 2110-30.
For more information about DDM, please visit Audinate's website.

SMTPE ST 2110
SMPTE ST-2110 is a video and audio IP network standard defined by SMPTE (Society of Motion Picture and Television Engineers). SMPTE ST-2110 is designed to separately embed and transmit video, audio, and ancillary signals, reducing the de-embedding processing load and network load of each device, while also enabling users to de-embed only the packet data they desire for further edit. ST-2110-30 realizes IP transmission of PCM digital audio, enabling high-precision synchronization using PTP (IEEE1588-2008) and low-latency transmission. It is expected to become a network standard protocol in next-generation broadcasting systems.

Primary and Secondary network connections redundancy and security
Primary and secondary connectors enable building a redundant system with a duplex network. Should the primary network route fails the ML-32D automatically switches to the secondary network route. This highly secure system prevents interruption and introduces no noise during the switch.

Flexible routing to connected Dante-compatible devices
The ML-32D uses Dante Controller to configure the main unit and to connect to other Dante-compatible devices. Dante Controller enables flexible routing configuration to other Dante-compatible devices.

Possible to interconnect with AES67 and Ravenna systems
Dante supports AES67, which enables audio connection with systems using AES67 and AES67-compatible protocols including Ravenna.

Integrated Signal/Overload indicator
The front panel is equipped with a signal/overload indicator that enables monitoring of analog input/output signals. The signal indicator turns on when a signal level becomes lower than –60dBFs.

5 selectable reference levels which can accommodate to a variety of scenes
The TASCAM ML-32D features selectable reference level setting from 5 maximum level options: +24dBu, +22dBu, +20dBu, and +18dBu (the standard level is +4dBu) and +15dBu (the standard level is +6dBu), which can accommodate to a variety of purposes including professional use in broadcasting studios, public address systems and recording environments.

Flexible choice of connectors according to purposes
ML-32D is equipped with D-sub 25-pin connectors as analog line input/output connectors, and combining with optional breakout boxes enables conversion to Euro Block and XLR.

Features:

Analogue-Dante-Analogue converter for 16 (ML-16D) or 32 (ML-32D) line-level audio channels
Dante interface allows up to 16/32 audio channels to be transferred over an Ethernet network

Two LAN connectors for primary and secondary networks provide redundancy
Flexible routing with ”Dante Controller” software
AES67 is supported to allow connection with Ravenna and other compatible audio network technologies
Compatible with SMPTE ST 2110-30


Up to 96 kHz sampling rate and 24 bit resolution
Indicators for operation status and current sample rate
Overload indicators for analogue input signals
Signal indicators for analogue input and output signals
Five different reference levels available to adapt to virtually any application in consumer, professional or broadcast environments (selectable via rear-side switches)
25-pin D-sub connectors for balanced line inputs/outputs (AES59-2012:TASCAM pin assignment)

Euroblock breakout box can be used for fixed installation (BO-32DE)
XLR breakout boxes can be used for live music or studio applications (BO-16DX/IN, BO-16DX/OUT)




19-inch rack-mountable chassis (1U)


Spec:



Ratings




Audio resolution
44.1/48/88.2/96 kHz, 16/24 bit






Analogue audio inputs




Connectors
D-sub 25-pin


Locking screws
No. 4-40 UNC (inch type)


Nominal input level
+4 dBu, +6 dBu (only when maximum input level is +15 dBu)


Maximum input level
+24 dBu, +22 dBu, +20 dBu, +18 dBu, +15 dBu(set by REF. LEVEL switches)


Input impedance
≥10 kΩ






Analogue audio outputs




Connectors
D-sub 25-pin


Locking screws
No. 4-40 UNC (inch type)


Nominal output level
+4 dBu, +6 dBu (only when maximum output level is +15 dBu)


Maximum output level
+24 dBu, +22 dBu, +20 dBu, +18 dBu, +15 dBu(set by REF. LEVEL switches)


Output impedance
≤200 Ω


Applicable load impedance
≥2 kΩ






Network inputs/outputs




Dante PRIMARY/SECONDARY
RJ-45 connectors


  Transmission protocol
Dante


  Network standard
Gigabit Ethernet, 1000BASE-T (IEEE 802.3ab)


  Cable requirements
Cat 5e or better STP cables






Audio performance




ANALOG IN to DANTE OUT


  Frequency response
20 Hz – 20 kHz, +0.1 dB / –0.5 dB(–16 dBFS input, 44.1/48 kHz sampling frequency, JEITA)20 Hz – 40 kHz, +0.1 dB / –0.5 dB(–16 dBFS input, 88.2/96 kHz sampling frequency, JEITA)


  Distortion (THD+N)
≤0.001 %(–1 dBFS input, 1 kHz, 44.1/48/88.2/96 kHz sampling frequency, JEITA)


  S/N ratio
≥113 dB(44.1/48/88.2/96 kHz sampling frequency, JEITA)


  Crosstalk
≥115 dB(1 kHz, 44.1/48/88.2/96 kHz sampling frequency, JEITA)


DANTE IN to ANALOG OUT


  Frequency response
20 Hz – 20 kHz, +0.1 dB / –0.5 dB(–16 dBFS input, 44.1/48 kHz sampling frequency, JEITA)20 Hz – 40 kHz, +0.1 dB / –1.0 dB(–16 dBFS input, 88.2/96 kHz sampling frequency, JEITA)


  Distortion (THD+N)
≤0.001 %(–1 dBFS input, 1 kHz, 44.1/48/88.2/96 kHz sampling frequency, JEITA)


  S/N ratio
≥110 dB(44.1/48/88.2/96 kHz sampling frequency, JEITA)


  Crosstalk
≥115 dB(1 kHz, 44.1/48/88.2/96 kHz sampling frequency, JEITA)






Power supply and other specifications




Power supply
AC 100–240 V, 50/60 Hz


Power consumption
ML-32D: 22 WML-16D: 14 W


Dimensions (W × H × D)
483 mm × 45 mm × 304 mm


Weight
ML-32D: 3.5 kgML-16D: 3.3 kg


Operating temperature range
0–40 °C